Double Your Power
The Fluke 787 was the first tool to combine a DMM and a loop calibrator to give process technicians double the power in one tool. Now it’s even better, the range is extended with the new Fluke 789 – the ultimate loop calibration multimeter. The Fluke 789 has a 24-Volt loop supply reducing the need for taking a separate power supply when doing offline transmitter testing. And with its built-in, selectable 250-Ohm Hart® resistor, it also eliminates the need to carry a separate resistor with you. Now process technicians can do a lot more while carrying a lot less.
Features of the Fluke 789
- 24 V Loop power supply
- Very large dual display
- Enhanced backlight with 2 brightness settings
- 1200 Ohm drive capability on mA source
- HART mode setting with loop power and a built-in 250 ohm resistor
- 0% and 100 % buttons to toggle between 4 and 20 mA sourcing for a quick span check
- Externally accessible fuses for easy replacement
- Infrared-port to process data in FlukeView Forms (V2.1) software
Fluke 789 features that are also included in the Fluke 787
- Precision 1000 V, 440 mA True-RMS digital Multimeter
- 0.1% dc voltage accuracy
- 0.05% dc current accuracy
- Frequency measurement to 20 kHz
- Min/Max/Average/Hold/Relative modes
- Diode Test and Continuity Beeper
- Simultaneous mA and % of scale readout
- 20 mA DC current source / loop calibrator / simulator
- Manual Step (100%, 25%, Coarse, Fine) plus Auto Step and Auto Ramp
- Externally accessible battery for easy battery changes
Safety Conformance
Meets 1000 Volt EN61010-1 CAT III standards and 600 Volt EN61010-1 CAT IV standards.
Specifications | |||||||||||||||
Current Measurement |
|
||||||||||||||
Current Sourcing |
|
||||||||||||||
Frequency |
|
||||||||||||||
Continuity |
|
||||||||||||||
Voltage measurement |
|
||||||||||||||
Resistance measurement |
|
||||||||||||||
Diode test |
|
||||||||||||||
Display current and % of span |
|
||||||||||||||
Auto step, auto ramp |
|
Environmental Specifications | |||||||||
Operating Temperature |
|
||||||||
Storage Temperature |
|
||||||||
Humidity (Without Condensation) |
|
||||||||
Temperature Coefficient |
|
Safety Specifications | |||||
Electrical Safety |
|
||||
Overvoltage category |
|
||||
Maximum voltage |
|
Mechanical & General Specifications | |||||
Size |
|
||||
Weight |
|
||||
Batteries |
|
||||
Warranty |
|
||||
Battery Life |
|
||||
Shock & Vibration |
|
Accessories common to all models:
Acessório | Descrição |
---|---|
AC175 |
Alligator Clip Set |
AC89 |
Heavy Duty Insulation Piercing Test Clip |
TL910 |
Sondas de teste eletrônicas |
TP912 |
Pontas de substituição para o TL910 |
FlukeView Forms |
Software para o FlukeView Forms |
TL80A |
Jogo de terminais de teste eletrônico básico |
TL71 |
Jogo de terminais de teste |
TL75 |
Hard Point™ Test Lead Set |
- Início
-
Produtos
- Novos Produtos
- Calibração elétrica
- Calibração de RF
- Equipamento de aquisição de dados e de teste
- Calibração de temperatura
- Calibração de umidade
- Calibração de pressão
- Calibração de fluxo
- Ferramentas de Calibração de processo
- Software de calibração
- Onde Comprar
- Notícias
- Treinamento e eventos
- Literatura e educação
-
Serviço e Suporte
- Service Request (RMA)
- Planos de Serviço
- Suporte técnico
- Base de Conhecimento
- Acreditações
- Centros de assistência autorizados
- Calibration Certificates
- Community Forum
- My MET/SUPPORT
- Manuais de produto (Guias de usuário)
- Registrar produtos
- Folhas de Dados de Segurança (SDS)
- Avisos de segurança
- Downloads de software
- Sobre Nós